| apparent power | 6.7 kVA at 240 V |
| prospective line Isc | 5 kA |
| continuous output current | 17.5 A at 230 V |
| maximum transient current | 19.3 A for 60 s |
| speed drive output frequency | 0.5…200 Hz |
| nominal switching frequency | 12 kHz |
| switching frequency | 6...16 kHz adjustable
12...16 kHz with derating factor |
| speed range | 1…10 |
| speed accuracy | +/- 10 % of nominal slip 0.2 Tn to Tn |
| torque accuracy | +/- 15 % |
| transient overtorque | 120 % of nominal motor torque +/- 10 % for 60 s |
| asynchronous motor control profile | Voltage/frequency ratio, 2 points
Voltage/frequency ratio, 5 points
Flux vector control without sensor, standard
Voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo)
Voltage/frequency ratio - Energy Saving, quadratic U/f |
| regulation loop | Adjustable PI regulator |
| motor slip compensation | Automatic whatever the load
Not available in voltage/frequency ratio motor control
Adjustable |
| local signalling | 1 LED (red) for DC bus energized |
| output voltage | ≤ power supply voltage |
| isolation | Electrical between power and control |
| type of cable | Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR
Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
With UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC |
| electrical connection | VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES: terminal 2.5 mm² / AWG 14
L1/R, L2/S, L3/T: terminal 6 mm² / AWG 10 |
| tightening torque | 1.3 N.m, 11.5 lb.in (L1/R, L2/S, L3/T)
0.6 N.m (VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES) |
| supply | Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, < 10 A, protection type: overload and short-circuit protection
Internal supply: 24 V DC (21…27 V), < 200 A, protection type: overload and short-circuit protection |
| analogue input number | 2 |
| analogue input type | VIA switch-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits
VIB configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits
VIB configurable PTC probe: 0...6 probes, impedance: 1500 Ohm
VIA switch-configurable current: 0...20 mA, impedance: 250 Ohm, resolution 10 bits |
| sampling duration | 2 ms +/- 0.5 ms F discrete
2 ms +/- 0.5 ms R discrete
2 ms +/- 0.5 ms RES discrete
3.5 ms +/- 0.5 ms VIA analog
22 ms +/- 0.5 ms VIB analog |
| response time | FM 2 ms, tolerance +/- 0.5 ms for analog output(s)
FLA, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
FLB, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
RY, RC 7 ms, tolerance +/- 0.5 ms for discrete output(s) |
| accuracy | +/- 0.6 % (VIA) for a temperature variation 60 °C
+/- 0.6 % (VIB) for a temperature variation 60 °C
+/- 1 % (FM) for a temperature variation 60 °C |
| linearity error | VIA: +/- 0.15 % of maximum value for input
VIB: +/- 0.15 % of maximum value for input
FM: +/- 0.2 % for output |
| analogue output number | 1 |
| analogue output type | FM switch-configurable voltage 0...10 V DC, impedance: 7620 Ohm, resolution 10 bits
FM switch-configurable current 0...20 mA, impedance: 970 Ohm, resolution 10 bits |
| discrete output number | 2 |
| discrete output type | Configurable relay logic: (FLA, FLC) NO - 100000 cycles
Configurable relay logic: (FLB, FLC) NC - 100000 cycles
Configurable relay logic: (RY, RC) NO - 100000 cycles |
| minimum switching current | 3 mA at 24 V DC for configurable relay logic |
| maximum switching current | 5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)
5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)
2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)
2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R) |
| discrete input type | F programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
R programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
RES programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm |
| discrete input logic | Positive logic (source) (F, R, RES), ≤ 5 V (state 0), >= 11 V (state 1)
Negative logic (sink) (F, R, RES), >= 16 V (state 0), ≤ 10 V (state 1) |
| acceleration and deceleration ramps | Linear adjustable separately from 0.01 to 3200 s
Automatic based on the load |
| braking to standstill | By DC injection |
| protection type | Overheating protection: drive
Thermal power stage: drive
Short-circuit between motor phases: drive
Input phase breaks: drive
Overcurrent between output phases and earth: drive
Overvoltages on the DC bus: drive
Break on the control circuit: drive
Against exceeding limit speed: drive
Line supply overvoltage and undervoltage: drive
Line supply undervoltage: drive
Against input phase loss: drive
Thermal protection: motor
Motor phase break: motor
With PTC probes: motor |
| dielectric strength | 2830 V DC between earth and power terminals
4230 V DC between control and power terminals |
| insulation resistance | >= 1 mOhm 500 V DC for 1 minute |
| frequency resolution | Display unit: 0.1 Hz
Analog input: 0.024/50 Hz |
| communication port protocol | LonWorks
METASYS N2
APOGEE FLN
Modbus
BACnet |
| connector type | 1 RJ45
1 open style |
| physical interface | 2-wire RS 485 |
| transmission frame | RTU |
| transmission rate | 9600 bps or 19200 bps |
| data format | 8 bits, 1 stop, odd even or no configurable parity |
| type of polarization | No impedance |
| number of addresses | 1…247 |
| communication service | Read device identification (43)
Write single register (06)
Read holding registers (03) 2 words maximum
Time out setting from 0.1 to 100 s
Write multiple registers (16) 2 words maximum
Monitoring inhibitable |
| option card | Communication card for LonWorks |
| operating position | Vertical +/- 10 degree |
| width | 142 mm |
| height | 184 mm |
| depth | 150 mm |
| net weight | 3.05 kg |
| power dissipation in W | 193 W |
| air flow | 66 m3/h |
| specific application | HVAC |
| IP degree of protection | IP21 |
| Variable speed drive application selection | Compressor for scroll Building - HVAC
Fan Building - HVAC
Pump Building - HVAC |
| Motor power range AC-3 | 4…6 kW at 200…240 V 3 phases |
| motor starter type | Variable speed drive |
